[Psymon]

Originally Posted by Decoy You flashed successfully ?? What did u do ?? We are trying to flash but we are getting verifying errors .. What did u do ??

Just as I said before, i used an old Bitstream. So i could correctly dump the NANDs. After patching there was no error at flashing the files to the NAND. I could enter the Factory Mode just as described.

[Decoy]

Originally Posted by Psymon Just as I said before, i used an old Bitstream. So i could correctly dump the NANDs. After patching there was no error at flashing the files to the NAND. I could enter the Factory Mode just as described.

Give us more info bro , like :

What winskeet u used , what options , what is your mobo ?
What did you do to r8 , r7 switches , did u power the ps3 from 3.3 or from power supply , tell us what u can tell , rescue us xD

[Psymon]

Okay here we go:

-PS3 Model CECHC04,
-Motherboard COK-002,
-Progskeet V1.2,
-360 Nand Clip 48,
-Winskeet Version 111205,
-Nothing changed with R7 or R8,
-Power supply via USB (3.3 V and GND from Progskeet to PCB Board),
-Bitstream Version 121018.0031,
-Slave Board switch on (LED is on) while connecting to PC, then switch off to dump,
-in Winskeet select double NAND Samsung K9F...,
-at NAND Register the NAND gets recognized via AUTO correctly,
-dump the NAND (hopefully without errors).

Hope this helps.
Greetz Psymon

[4DoorITR]

What about writing? I think that this is where everyone is encountering issues. I have dumped a Spansion fine but can't get the Progskeet 1.2 to write anything back without 100% verification errors. Thanks.

[M8nTrap]

hello

my progskeet slave board doesn't work, no glowing green and be hot quickly after some second.

(the 15 pin flat ribbon, work perfectly with the injectus...not with the progskeet slave board)

after looking at the 15 pin flat ribbon, it doesn't match perfectly with the progskeet slave board connector...

he makes faulty contacts, short circuits... or readings and writings with errors.

i have contacted my reseller for a exchange...

[Psymon]

Writing did work at first try. Doesn't know exactly at which position the switch at the slave board was. Cannot say much more about it. Just pressed AUTO and the Nand was recognized and after that pressed write. No verification errors.

[amined]

Originally Posted by Psymon Okay here we go: -PS3 Model CECHC04, -Motherboard COK-002, -Progskeet V1.2, -360 Nand Clip 48, -Winskeet Version 111205, -Nothing changed with R7 or R8, -Power supply via USB (3.3 V and GND from Progskeet to PCB Board), -Bitstream Version 121018.0031, -Slave Board switch on (LED is on) while connecting to PC, then switch off to dump, -in Winskeet select double NAND Samsung K9F..., -at NAND Register the NAND gets recognized via AUTO correctly, -dump the NAND (hopefully without errors). Hope this helps. Greetz Psymon

NOT WORK FOR ME

[Psymon]

Do you also have a CECH04?? Did Winskeet recognize your NAND? What is not working???

[mmmilo]

hi
I'm afraid my prgskt v 1.2 doesnt work, because after updating bitstream with injectus following message appear in injectus window

ACTEL_SLOG_UROW =
FF FF FF FF FF FF FF FF FF FF FF FF FF 00 FF FF

Programming UROW...

Programming FPGA Array...

gues this should look otherwise like A5 56 F4 etc.

or is everything fine with my prgskt v 1.2
************* [ - Post Merged - ] *************
does someone not use the nandclip? i will go for soldered method and found the alternate points for my cechg04 sem 001 board i gues.
According to wiki i should use the bitstream for soldered

"ProgSkeet_Bitstreams_111106.rar (1.63 MB) (NOR solderless and NOR+NAND soldered) "

[amined]

Originally Posted by Psymon Do you also have a CECH04?? Did Winskeet recognize your NAND? What is not working???

- Winskeet recognize my NAND for the first time when i press Auto
if i press again just after i see UNKNOWN

- I have CECH04 cok-002w

i have only bad dump
verify my dump if you like


(http://www.fileswap.com/dl/cUZRIclJlU/)