|
|
11-22-2012
|
#1 |
|
Member
 Join Date: Nov 2012
Posts: 40
Likes: 3
Liked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
progskeet v1.2&WinSkeet problems
Hi,
i have progskeet v1.2(last Bitstreams) with the 360 clip 48 pin for nand i make 2 wire from 3.3V and GND progskeet to 3.3V and GND pcb but i have problem with WinSkeet please help me  please help me Last edited by amined; 11-22-2012 at 04:58 PM. |
|
|
|
11-22-2012
|
#2 |
|
Member
Join Date: Nov 2012
Posts: 40
Likes: 3
Liked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Last edited by amined; 11-23-2012 at 08:21 AM. |
|
|
|
|
11-22-2012
|
#3 |
|
Senior Member
 Join Date: Dec 2011
Posts: 4,441
Likes: 965
Liked 1,545 Times in 1,112 Posts
Mentioned: 796 Post(s)
Tagged: 0 Thread(s)
|
I have the same problem, but with v1.1.
It is because the clip is not on good enough. The 360 clip is unreliable and it is probably best to learn how to solder.
__________________
HOW TO DOWNGRADE W/E3 FLASHER TO ANY OFW/CFW
Nor model PS3 downgrade service in U.S.A. if you don't want to do it yourself For downgrade help join irc at effnet-Just enter name and channel is #ps3downgrade |
|
|
|
11-23-2012
|
#4 |
|
Member
Join Date: Nov 2012
Posts: 40
Likes: 3
Liked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
i think that me too
but in my case The 360 clip is good working because the winskeet is organize the nand Last edited by amined; 11-23-2012 at 06:16 AM. |
|
|
|
|
11-23-2012
|
#5 | |
|
Senior Member
Join Date: Dec 2011
Posts: 4,441
Likes: 965
Liked 1,545 Times in 1,112 Posts
Mentioned: 796 Post(s)
Tagged: 0 Thread(s)
|
IDK   Soldering the flasher would be the most reliable way to do it.
__________________
HOW TO DOWNGRADE W/E3 FLASHER TO ANY OFW/CFW
Nor model PS3 downgrade service in U.S.A. if you don't want to do it yourself For downgrade help join irc at effnet-Just enter name and channel is #ps3downgrade |
|
|
|
|
|
11-23-2012
|
#6 |
|
Apprentice
 
Join Date: Nov 2012
Location: NS
Posts: 11
Likes: 0
Liked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Sell clips good advice !!!
Always solder no problem to read and write!!! Only progskeet 1.1 or 1.0, 1.2 does not write this ****!!! |
|
|
|
|
11-23-2012
|
#7 |
|
Member
Join Date: Nov 2012
Posts: 40
Likes: 3
Liked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
thank's all for reply
ok i will do but i need the diagram for cok-002 w 2 nands on top  
Last edited by amined; 11-23-2012 at 09:39 AM. Reason: add pic |
|
|
|
|
11-23-2012
|
#8 | |
|
Apprentice
Join Date: Nov 2012
Location: NS
Posts: 11
Likes: 0
Liked 1 Time in 1 Post
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
|
|
|
|
|
|
11-23-2012
|
#9 |
|
Member
Join Date: Nov 2012
Posts: 40
Likes: 3
Liked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
solder direct on the nand is very hard for me
is exist same solution like this ???????? 
Last edited by amined; 11-23-2012 at 05:56 PM. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
|
|
