|
|
12-01-2012
|
#1 |
|
Apprentice
 Join Date: Dec 2012
Posts: 14
Likes: 1
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Downgrade help
I am after a little help from you kind people out there if possible.
Today I spent a lot of time trying to downgrade using the E3 flasher and the E3 card reader and got as far as installing OFW3.55, however, immediately after this I now get the flashing red light. Looking back at the tutorial I followed, I stupidly missed the point that after running the toggle_qa.pkg if I get a black screen I need to remarry the Bluray drive. I missed this and continued to install OFW 3.55 Can anybody point me in the right direction please, I would be most appreciative. |
|
|
|
12-01-2012
|
#2 |
|
Senior Member
 
Join Date: Oct 2012
Posts: 1,830
Likes: 388
Liked 430 Times in 345 Posts
Mentioned: 355 Post(s)
Tagged: 0 Thread(s)
|
Start again flash your initial dump and try console
|
|
|
|
|
12-01-2012
|
#3 |
|
Apprentice
Join Date: Dec 2012
Posts: 14
Likes: 1
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Apologies for my complete lack of knowledge on this, but are you suggesting start the tut from the beginning again?
|
|
|
|
|
12-01-2012
|
#4 |
|
Senior Member
Join Date: Oct 2012
Posts: 1,830
Likes: 388
Liked 430 Times in 345 Posts
Mentioned: 355 Post(s)
Tagged: 0 Thread(s)
|
Yes but first the dump you made the first time flash that back and test console
|
|
|
|
|
12-01-2012
|
#5 |
|
Apprentice
Join Date: Dec 2012
Posts: 14
Likes: 1
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I cannot re-flash as the console does not load to the XMB.
Straight to flashing red light. |
|
|
|
|
12-02-2012
|
#6 |
|
Senior Member
Join Date: Oct 2012
Posts: 1,830
Likes: 388
Liked 430 Times in 345 Posts
Mentioned: 355 Post(s)
Tagged: 0 Thread(s)
|
Use hardware flasher
|
|
|
|
|
12-02-2012
|
#7 |
|
Apprentice
Join Date: Dec 2012
Posts: 14
Likes: 1
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
The power is cut to my E3 Flasher when the console shuts down to the flashing red lights.
|
|
|
|
|
12-02-2012
|
#8 |
|
Senior Member
Join Date: Oct 2012
Posts: 1,830
Likes: 388
Liked 430 Times in 345 Posts
Mentioned: 355 Post(s)
Tagged: 0 Thread(s)
|
Power externally or solder transate to sbe
|
|
|
|
|
Likes: (1) |
|
12-02-2012
|
#9 |
|
Apprentice
Join Date: Dec 2012
Posts: 14
Likes: 1
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Thank you, I will give this a shot.
|
|
|
|
|
12-02-2012
|
#10 |
|
Apprentice
Join Date: Dec 2012
Posts: 14
Likes: 1
Liked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Ok, so I've soldered the wire and flashed my original dump back on with switch 1 up and 2-5 down, but my console still wont boot. Stuck at the flashing red light.
Any ideas, I'm at a loss again? |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
|
|
