[Mr.Dutch]

@monu1232009 , asked me to make a thread again about his problem, i hoped he would have solved it by now, but it turns out this problem is harder then it looks.
@baileyscream and @playerkp420 allready helped in the past, and for the moment i have no clue how to help other then to make this thread.
---------------

ps3 history: bricked from rogero 4.21 update install.
ps3 model: chech2508b
downgrader: e3 linker installed
ps3 symptoms: no video no audio or hdd {signs of glod}

[quote=monu1232009]
i started with installing e3 flasher via clip and made 4 original dumps.
then i checked them as shown in bailey's guide.
@MJ999 checked my dump and said it was ok, i did not get response from other members.

i patched it and tried to flash it to my console but i got an error at the middle of writing to the nor chip.
at this point i found that my e3 clip was faulty and not seated properly, then i decided to install e3linker with nor test point.

i flashed my console via e3 linker, but my ps3 did not recover from brick, i contacted sir baily and playerkp420.
they asked to check the linker connection, i checked and everything was ok.

then they asked for 1 key downgrade but i did not work then playerkp420 asked me to replace thermal paste i have done it but it also did not work.
sir bailey asked me to make thread with full story of my ps3.
following link contains my 4 nor dumps.

post edited, links are not valid anymore.

and i have to admit this is not my territory, so any help or ideas are welcome.
we need lots of input, yeah i'm talking also to you @Bigbones87

[monu1232009]

thanks for making this thread

[Bigbones87]

I can try to help as much as possible. If playerkp420 and bailesycream already made an attempt to help with no success, not too sure I can be of service. They know more asleep than I do awake. Link me to the thread with all the ins and outs already attempted so I can be better informed and try to help as much as possible.

[redtree]

bkpps3.bin - BAD as mentioned already
bkpps30.bin - BAD (repeated data starting at 00F00010 ["faceoff faceoff" instead of "faceoff deadface"] to 00F00170)
bkpps31.bin - Seems your best bet from the 4 dumps provided
bkpps32.bin - BAD (repeated data throughout ros1)

That's my quick look at them. I'm not experienced enough to suggest how to fix the problem, I would think bkpps31.bin may give the best chance of video and hard drive activity. As E3 linker is now used, double check address wires are correct. Good luck!

[monu1232009]

thank you so much red tree today i will check my connection of e3 then report at this thread.

[baileyscream]

Originally Posted by monu1232009 i think there is somthing wrong with mediafire please try this link http://uploads.boxify.me/96354/bkpps3.rar?1354564063

Originally Posted by baileyscream yep i have this one i wont be long

Originally Posted by monu1232009 sir what do you think about these ofset of my dump , are these normal. 00fc0000 00 00 2f 53 53 e6 a0 bb b0 af az 00 67 d0 b3 9a 00f00010 00 00 00 00 0f ac e0 ff 00 00 00 00 0f ac e0 ff

Originally Posted by baileyscream 00FC000 00 00 2F 53 53 E6 A0 BB B0 AF A2 00 67 D0 B3 9A 00FC010 00 00 2F 53 29 D3 71 F5 FA 78 CE 2A 99 D9 F4 2F there right my other message i was wrong you dont just have FF FF FF FF FF FF FF FF FF FF where info should be but you have info where FF FF FF FF FF FF FF FF should be its still down to the clip i think though can you send me the actual dump you flashed bkpp3.bin (your origional dump) please

Originally Posted by monu1232009 it is the dump that i mode from other 4 dump's good part will this work?

Originally Posted by baileyscream this is a really bad idea you need to insure that clip is on good or the wires are soldered good. then create a dump. if you have some sections bad then there is a 90% chance that the encripted part of the dump also has sections bad and as its encripted there is no way to check this. i would suggest you open a thread and post everything you have done so far include our messages and hopefully afew of us can bounce ideas about between us for the beas possible way to fix this.

Originally Posted by monu1232009 sir it was not my idea that my dump is valid and there was no need to do more dums but in dump checking thread a person mj999 told me this is valid and when i asked for double check there was no respons.it was too late when i knew that my clip is faulty from a side . and if you check all of my dump{3,30,31,32} you will know that 31 is good one only a small part of it is bad{which stars at AA8010 to AA9500 something} and this bad part is good at other 3 dump you can easily see in hex editor . please sir help me if you can. and please tell me a difference between glod and bricked from rogero cfw {no video no hdd}.

Originally Posted by baileyscream ok give me your very first dump. dont send the byte reversed one but your very first one and the link for your new one.

Originally Posted by monu1232009 ok sir at following link you will get 30 31 and 32. {31 is good with a small bad part} http://www.mediafire.com/?erleln6obo2osgg and at this link you will get the moded 31 dump with no bad part. http://www.mediafire.com/?j61yve5c9n2th3g thank you for helping me...

Originally Posted by baileyscream no your very first dump the first good one you had when you first connected your E3

Originally Posted by monu1232009 hello sir is there any hope for my console.?

still waiting for that very first dump NOT the byte reversed one you had checked by mj999 but your very first dump.
or winrar all your dumps every single one of them and upload
there may be 1 good one there

[playerkp420]

Originally Posted by baileyscream still waiting for that very first dump NOT the byte reversed one you had checked by mj999 but your very first dump. or winrar all your dumps every single one of them and upload there may be 1 good one there

@monu1232009

I have a whole folder of dumps from monu. I have this one labeled valid. It was the first one I checked for him.

Maybe I missed something and its not valid? Could someone check it.

If it is valid and you can not unbrick with it. I would say reseat the clip or check the soldering.

[Mr.Dutch]

ps3 symptoms: no video no audio or hdd {signs of glod}

@monu1232009 , do you actually have a green light of death when you start the ps3?, it's not going back to standby mode with a blinking red light?

i want to rule out hardware issues, since your problem also involved a broken power connector.

@Bigbones87 , there was a thread before this one, but was hardware related (broken power connector), i think the most help was done in private posts.

link to original thread:

http://www.ps3hax.net/showthread.php...t=corrupt+bios

[monu1232009]

Originally Posted by baileyscream still waiting for that very first dump NOT the byte reversed one you had checked by mj999 but your very first dump. or winrar all your dumps every single one of them and upload there may be 1 good one there

i have given you my first dump which was checked by mj999. its name is bkps30.bin
************* [ - Post Merged - ] *************
yes when i start my ps3 it is not going back stand by mode. i have to hold reset button for 15 to 20 sec to get stand by mode...
************* [ - Post Merged - ] *************

Originally Posted by Mr.Dutch @monu1232009 , do you actually have a green light of death when you start the ps3?, it's not going back to standby mode with a blinking red light? i want to rule out hardware issues, since your problem also involved a broken power connector. @Bigbones87 , there was a thread before this one, but was hardware related (broken power connector), i think the most help was done in private posts. link to original thread: http://www.ps3hax.net/showthread.php...t=corrupt+bios

do i need to check some fuses
************* [ - Post Merged - ] *************
it is my all backup dump link.
http://www.mediafire.com/?vl5ni5fztwnqd3u

[Mr.Dutch]

[QUOTE=monu1232009;496702do i need to check some fuses[/QUOTE]

i only asked because i wanted to know if the 12V would come to life, if the fan is running then it's alive.
no 12V would mean blinking red light when trying to start the ps3, tested it out myself.

in your case it looks like the ps3 hangs on bootup?
i'm guessing the fan gets it's power, so is the bluray drive and usb ports.

but i'm usually not good in guessing.