[3absiso]

Originally Posted by arcadekidflo Anyone got the chance to look at my backup ? Should i have sent it attached to the email or uploaded somewhere ?

I am on it

Edit: Your Dump is Valid

[arcadekidflo]

Seemed ok to me too , but after patching it and flashing it console gets no video / HDD / USB . Good thing is that it does stay on , unlike other bricks

Only warning in BWE Validator were

Asecure_Loader/Metldr Encrypted Statistics: Sum: 59616 ✔ Mean: 232.875 ✔ Std Dev: 17.6319674032651 - [WARNING]

and

00 / FF / Other Statistics: 18.24% [WARNING] - Patch & Recheck (Risky below 18.24) 10.46% ✔ 0.28% ✔

I'm more concerned about the one in the asecure_loader / metldr area , what is STD DEV ?
Atm , console does stay on and the NOR is flashing , would soldering the wire to the Tristate make any difference in the attempt of unbricking ?

[3absiso]

Originally Posted by arcadekidflo Seemed ok to me too , but after patching it and flashing it console gets no video / HDD / USB . Good thing is that it does stay on , unlike other bricks Only warning in BWE Validator were and I'm more concerned about the one in the asecure_loader / metldr area , what is STD DEV ? Atm , console does stay on and the NOR is flashing , would soldering the wire to the Tristate make any difference in the attempt of unbricking ?

Open a new thread describing your problem

[iC3s3Rv3D]

Please Check My Dump I Sent it 2 minutes ago THANKS

/\ that sounds so wrong!

[MJ999]

Originally Posted by iC3s3Rv3D Please Check My Dump I Sent it 2 minutes ago THANKS /\ that sounds so wrong!

YOUR DUMP IS FALID

[danguy2009]

Have sent my dump for checking. It is from a RSOD CECH-L03 on 4.31. Have checked through it according to the wiki and seems fine there but run it through BWE 1.11 and getting warning on the ECID, the similarities of the ECID match what is in the wiki for the ECID so could be fine maybe Have dumped it 7 times and got three of the dumps to match after having the console to the bare motherboard with my thumb pressing on the clip

[mazenico]

Hi there i sent my dump

Thanks for your willingness

[BwE]

Originally Posted by arcadekidflo I'm more concerned about the one in the asecure_loader / metldr area , what is STD DEV ? Atm , console does stay on and the NOR is flashing , would soldering the wire to the Tristate make any difference in the attempt of unbricking ?

In statistics and probability theory, standard deviation shows how much variation or "dispersion" exists from the average (mean, or expected value). A low standard deviation indicates that the data points tend to be very close to the mean; high standard deviation indicates that the data points are spread out over a large range of values.
************* [ - Post Merged - ] *************

Originally Posted by danguy2009 Have sent my dump for checking. It is from a RSOD CECH-L03 on 4.31. Have checked through it according to the wiki and seems fine there but run it through BWE 1.11 and getting warning on the ECID, the similarities of the ECID match what is in the wiki for the ECID so could be fine maybe Have dumped it 7 times and got three of the dumps to match after having the console to the bare motherboard with my thumb pressing on the clip

PM your ECID Its more than likely not an issue. Some ID's are rare and thus are indicated as WARNING until I can know for sure that they are legit/valid.
************* [ - Post Merged - ] *************

Originally Posted by arcadekidflo Email sent , please help me out guys , dump seemed fine but console bricked BWE Validator gave a warning about 00's but i read here that it's ok if you're on 4.31

That is correct

[danguy2009]

Originally Posted by BwE PM your ECID Its more than likely not an issue. Some ID's are rare and thus are indicated as WARNING until I can know for sure that they are legit/valid.

PM'ed ..........

[BwE]

Originally Posted by danguy2009 PM'ed ..........

Cheers. I added your differences to my detection. It was off by 1 letter.